1. Home
  2. /
  3. Floor Seals - Single Component
  4. /
  5. Waterthane Floor Seal / Varnish

Waterthane Floor Seal / Varnish

£15.83£174.15

Product Information

Properties:  Moor Floor Finishes WATERTHANE floor seal / varnish produces a flexible, light-fast and water resistant seal which is hard, tough and abrasion resistant.
 
Description:  Moor Floor Finishes WATERTHANE floor seal / varnish is a specifically formulated single pack water based polyurethane modified with acrylic.
 
Available in:  Gloss, Satin and Matt finish.
 
Uses:  Moor Floor Finishes WATERTHANE floor seal / varnish has been developed for use on new or resanded Hardwood, Mosaic, Block, Cork and Softwood flooring, and produces a hard wearing and chemically resistant finish that is easily maintained. It is suitable for use in both commercial and domestic areas, and for recoating pre-finished flooring.
 
Preparation / Application:
Surfaces to be treated should be cleaned, degreased and previous polishes/treatments/finishes removed.
Apply Moor Floor Finishes WATERTHANE floor seal / varnish evenly using an 12″ Applicator or 20″ Applicator  &  Applicator pad , roller or soft brush. Take care not to leave pools, runs or drip marks, which will detract from the overall appearance of the floor. If the floor is to be left overnight before recoating, it is important that the surface is lightly abraded using a suitable grade of sandpaper or sandscreen / mesh disc to ensure good adhesion of the finish.
Once the final coat has been applied, the floor should be left for a minimum of 48 hours prior to light traffic being permitted. The finish will continue to cure and harden for a period of 5 days.
Cleaning chemicals should be avoided during this period
 
How to apply Waterthane video
 
Cleaning, Abrading & Resealing:
Floor surfaces should be scrubbed with an alkaline degreasing solution, rinsed and neutralised with Moor Floor Finishes NEUTRAL FLOORCLEAN  or MULTI-PURPOSE CLEANER .  The floor should then be rinsed clean and allowed to dry thoroughly. When dry apply a coat of WATERTHANE floor seal / varnish and allow to dry (2–3 hours depending on temperature and humidity). Apply a second coat within 24 hours to obtain maximum adhesion between coats. Ensure that there is adequate ventilation whilst the seal is drying. The coating should be allowed to cure for 48 hours before allowing light traffic.
When over coating previously finished floors, two coats of WATERTHANE floor seal / varnish are recommended.
 
Sanding & Sealing:
Ensure that the floor surface is free from oil, wax, grease, dirt and previous treatments. After sanding ensure all dust has bee removed by vacuuming or tac ragging. Floors which have been previously waxed or oiled it is recommended a primer coat of Moor Floor Finishes PRE-SEAL is used to prevent rejection or to reduce porosity. Apply a first coat of WATERTHANE floor seal / varnish and allow to dry (2–3 hours depending on temperature and humidity).  Any Line/court marking should be completed at this stage if required. Raising may occur on some types of wood grain and it will be necessary to buff back, in which case the first coat should be left for 3 to 4 hours.
Apply a second coat and third coat (if required) of WATERTHANE floor seal / varnish within 24 hours of each other to obtain maximum adhesion between coats.
Ensure that there is adequate ventilation whilst the seal is drying. The coating should be allowed to cure for 48 hours before allowing light traffic.
When coating refurbished Wood, Cork or Chipboard floors, three coats of WATERTHANE floor seal / varnish are recommended to provide a hardwearing finish.
 
Maintenance:  The sealed floor should be damp mopped or a Scrubber/drier used with a solution of Moor Floor Finishes NEUTRAL FLOORCLEAN . To prevent the build up of grease / fatty matter on the surface of the coating it should be scrubbed periodically with a mildly alkaline solution, such as Moor Floor Finishes MULTI-PURPOSE CLEANER .
 
Coverage:  Approximately 10 – 20 sqm per Litre depending on porosity of the surface.
 
Drying Time:  3 hours depending on temperature, humidity and ventilation.
 
Shelf Life:  2 years if left unopened. Stored in a cool, dry place & protected from frost.
 
Discounts:
2.5% Discount on 10 Litre Packs
5% Discount on 20 Litre Packs
For further Quantity Discounts please call 01773 828111 or Email for a quotation.
 

Video’s of WATERTHANE in use:  
Pine Softwood Strip Flooring, Repaired, Sanded & Sealed with first coat Pre-Seal, Coats 2 & 3 Waterthane
Oak Hardwood Strip Flooring Sanding & Sealing with Coat 1 Pre-seal, Coats 2 & 3 Waterthane
 
Before & After photo’s of WATERTHANE in use:
Moor Floor Finishes Gallery page

Related Products

Menu